· Build Videos, Mk1 Escort Videos

Fitting the Home-Made Sump to the ST170 – Dave's Garage Zetec RWD Mk1 Escort Ep 12

Dave's Garage UK Zetec RWD Mk1 Escort – Episode 12 title card: fitting the home-made sump

With the gearbox side of the swap finished in Episode 11, Dave’s Garage UK turns back to the bottom of the engine. The rear-drive sump he made earlier in the series finally goes on the ST170, sealed with nothing but RTV silicone. It’s the last job before the engine can be mocked up in the Escort’s engine bay.

Video: Dave's Garage on YouTube · watch “Ford Escort MK1Project. RWD Zetec Conversion. Fitting the Sump” on YouTube

What happens in Episode 12

A bare engine on the crane (around 2:46). The ancillaries are already stripped off, and rather than set up an engine stand he works with the engine hanging from the crane, which he admits is sketchy. Gloves go on, because old engine oil isn’t good for your skin.

Getting the factory sump off (4:05). His first bolts, undone with an 8 mm socket, turn out to hold a smaller section; he wants everything from there down, so he switches to a 10 mm socket and wedges the sump apart. It won’t drop clear while the oil pickup pipe is in place, so he refits a couple of bolts to hold the sump, takes the pickup off first, then removes the rest.

Let it drip (9:30). He leaves the engine hanging for a few hours so the worst of the oil drains off. He’s learned the hard way that if the mating faces aren’t perfectly clean, dry and grease-free, the silicone won’t stick and the sump will leak.

A clash on the dry fit (12:04). Offered up dry, the edge of his sump catches near the crank at the flywheel end, and possibly on the other side too. He rounds off the corners, snipping them rather than grinding so no grinder dust ends up in the engine.

Cleaning (13:26). Brake cleaner and wiping go on both the block and the sump, which looks clean but isn’t. Working upside down helps, as the spray drips off rather than running into the block.

A home-made pickup gasket (17:43). He makes a gasket for the pickup pipe from Flexoid gasket paper bought cheaply on eBay, probably 1 mm thick. Tapping round the flange with a ball-pein hammer marks out the holes, a bolt holds it in place while he works round, and the outline is drawn and cut out. He won’t trust the old cornflakes-box trick on a part as crucial as the oil pickup.

Sealing the sump (20:38). He squeezes a little RTV out first to clear the nozzle, then runs a bead round the flange. He’s learned not to be too shy with it, and in his experience it doesn’t fall into the engine, but don’t go mad with a huge bead. Lowering the sump on without smearing silicone everywhere is the trickiest part. Once tightened, he leaves the squeeze-out, perhaps trimming it with a blade after it sets.

Checking clearance (23:33). The bumps on the sump’s sides are there because the ST170’s conrods are much chunkier than a normal Zetec’s, so he turns the engine over to confirm nothing catches. It all clears.

Tips from the video

  • Clean is everything. Spend more time degreasing than fitting; oily faces mean leaks.
  • Dry fit first. It caught the sump-to-crank clash before any sealant went on.
  • Getting it off again. A sump sealed this way will come off with some encouragement and a thin blade started in the joint, without bending it out of shape.

Mk1 context

Dave calls the ST170 a monster of an engine, with a fantastic bottom end, and reckons a bare one costs about £300 to £400. In his view that’s money well spent, as building an ordinary Zetec or a Pinto to the same spec would cost a lot more. He also plans to make his own mounts rather than buy from Retro Ford, whose parts he rates but finds pricey because they take so much labour to make.

Still to sort

  • Mocking up in the shell. Next comes setting the engine and gearbox in the Escort to work out the engine mounts and where the box sits.

Mk1 EscortZetec