· Build Videos, Mk1 Escort Videos

DIY Gearbox Mounts on BMW Bobbins – Dave's Garage Zetec RWD Mk1 Escort Ep 15

Dave's Garage UK Zetec RWD Mk1 Escort – Episode 15 title card: DIY gearbox mounts on BMW bobbins

At the end of Episode 14 the ST170 sat level and square on its new engine mounts, but the back of the MX-5 gearbox was still held up by a temporary cradle Dave had rigged up. In this video, Dave’s Garage UK gives the gearbox a proper mount, made from 6 mm plate, nuts and bolts and a pair of BMW 3 Series gearbox bobbins. It turned out easier than he expected.

Video: Dave's Garage on YouTube · watch “Ford Escort MK1 Restoration Project, DIY Gearbox Mounts, Zetec RWD, Mazda MX5 Gearbox” on YouTube

What happens in Episode 15

Working from the pit (1:20). This is the first look at Dave’s inspection pit, which he dug about 20 years ago and counts as one of the best things he’s done. It’s tight for filming.

Fine threads (1:46). The mounting points on the MX-5 gearbox won’t take an ordinary M10 bolt. They need M10 x 1.25 metric fine, not the usual M10 x 1.5.

Placing the bobbins (2:35). The gearbox hangs down a long way, so there’s plenty of depth for two bobbins. Holding them where he wants them puts them about 40 mm forward of the gearbox’s mounting holes and about 50 mm to the side.

Bracket plates (3:47). As with the engine mounts, he makes a scrap-steel drilling guide and clamps it under the plate, so the holes that bolt to the gearbox come out square and accurate. The other holes don’t need to be as precise, so they’re just punched. “If it works it ain’t stupid.” The plates are then cut out with the plasma cutter.

A flaw, then a fix (9:57). While drilling he notices that the plate won’t fully support the bush. A trial fit under the car shows the idea works, though, and a brainwave sorts it out. The bobbins have a small locating nib, so a new hole for the nib lets them move in a little. One hole drilled straight across left the bush overhanging. He welded it up and redrilled it at an angle, and now the bush is supported on both sides.

Where to fix the cradle (12:40). Running the cross-plate over the floor’s strengthening plate would let it pivot downwards, and that area is on a slant inside. Instead, he uses two flat spots where the gearbox tunnel overlaps the floor by about an inch. That makes a strong flange to bolt through.

The cross-plate (14:37). An oblong piece of 6 mm plate happens to lie fairly flat against the floor. He averages his two marks so the holes are symmetrical, then drills up through the floor pan. Corners are rounded to clear floor features, and speed holes take out some weight without weakening it much.

Captive bolts (20:31). The holes are countersunk and bolts welded in, so the cradle can be offered up from underneath and fastened from inside by one person. Rather than wait for parts in the post, he machines a couple of bolts with a chamfer on top, fills it with weld, and keeps them bolted up square while welding.

Fitted (23:47). The temporary support comes off. Big washers on top, off-cuts of tough 2 mm plate, spread the load through the floor. Painted and bolted up, the gearbox sits on its rubbers with a good contact patch, and the bracket takes Dave’s weight when he hangs off it.

Tips from the video

  • Support the whole bush. Check that the bracket supports the rubber on both sides, not just through the bolt.
  • Bolt to the strong bits. The tunnel’s overlap with the floor gives a double-thickness flange that won’t let the plate pivot.
  • Build it, then prove it. If it cracks or bends later, strengthen it then.

Still to sort

  • Proving it on the road. Dave doesn’t expect trouble, since the engine mounts take most of the weight and the torque is spread out, but the floor washers may need to be larger or oblong.
  • Carried over from Episode 14: the gear-lever surround in the cut-back tunnel, a new cam-cover breather outlet and the replacement VVT solenoid.

Mk1 EscortZetec