· Build Videos, Mk1 Escort Videos

Fitting the ST170 Starter and Finishing the Gearbox Swap – Dave's Garage Zetec RWD Mk1 Escort Ep 11

Dave's Garage UK Zetec RWD Mk1 Escort – Episode 11 title card: ST170 starter fitted and the gearbox swap finished

Since the thick adaptor plate went on in Episode 9, the old Ford-pattern starter motor had jammed against the bellhousing. In the eleventh video of the Zetec RWD playlist, Dave’s Garage UK fits a starter from the ST170 engine itself, reworks the adaptor plate to suit, and declares the gearbox conversion finished, with a full rundown of the parts and lessons.

Video: Dave's Garage on YouTube · watch “Ford Escort MK1 Restoration. MX5 NA Gearbox onto Zetec part 5” on YouTube

What happens in Episode 11

A £40 starter (1:13). He found a nearly new ST170 starter on eBay for about £40. Coming from the same engine, its pinion is sure to suit the flywheel, and a temporary fly lead proves it spins.

Finding the right spot (around 2:30). For the teeth to mesh properly, the flat on the starter nose should almost touch the flywheel. None of the existing holes line up. The plate still flexes on its own, so he clamps it to the block first, then clamps the starter in place. The first try is too close; after moving it, the pinion throws out, spins the flywheel and drops back.

Drilling and welding (6:23). With the starter clamped, he drills 10 mm holes, bolting each down before the next so nothing shifts. The old holes are welded up, backed by an aluminium pipe-bender guide as he couldn’t find his copper block. He expected warping, but the plate stayed flat.

Studs instead of bolts from behind (10:39). Bolts fitted from behind the plate would be trapped by the gearbox, so changing the starter would mean taking the box off. Instead he bevels some bolts in the lathe, welds them into chamfered holes as permanent studs and grinds them flush, then does the same for the gearbox bolts. The adaptor plate is complete.

Flywheel, clutch and box (12:45). The clutch is now a 1.8 Mondeo flywheel and pressure plate with a 1.8 MX-5 clutch disc, which he says is a better combination than the Mazda 626 disc from Episode 9. The MX-5 release bearing sits nicely too. With the gearbox back on, the starter turns the engine over and the gears and clutch work.

Parts he lists for the swap (17:36)

  • About 400 x 400 mm of 1.2 mm sheet for the template, and 400 x 400 mm of 6 mm plate for the adaptor
  • 10 mm countersunk bolts, ideally grade 10.9 as they cost little more than 8.8, plus 12 mm countersunk machine screws and 10 mm and 12 mm nuts
  • The starter from the engine you’re fitting (for him, the ST170)
  • A 1.8 Mondeo flywheel for the 220 mm clutch (there’s also a 240 mm version, so check), a 1.8 Mondeo 220 mm pressure plate, and an early 1.8 MX-5 clutch disc from an NA or NB
  • The MX-5’s own release bearing, and a hybrid propshaft from a specialist

Lessons for your own Mk1

  • Start with the right starter. He learned the hard way that using the engine’s own starter from day one saves grief.
  • Clamp out the flex. Locate parts on a rigid plate, or they’ll be wrong once bolted up.
  • Think about access. Welded studs let the starter come off without removing the gearbox.
  • Pilot bearing. He’s pulled it about 3 mm out of the crank so it sits at the edge. If it causes trouble on the road, the fallback is a short pilot bearing extension, which means taking a little off the input shaft.
  • Consider an RX-8 box. He says it’s easier to adapt because its input splines suit the Ford clutch, and adaptor plates are sold on eBay for about £100.

Still to sort

  • Clutch release. Hydraulic or cable is still to be decided once it’s in the car, though he leans towards hydraulic.
  • Fit in the shell. On his measurements it should fit, with the steering shaft sitting lower than the box.

Mk1 context

He reckons the lever could go another 1.5 to 2 inches beyond the four already moved, so the MX-5 box could suit other rear-drive classics as well as the Mk1.

Mk1 EscortZetec